Air Ducts For Mobile Homes

heating system, crossover duct, Air Ducts For Mobile Homes

Why Mobile Homes Flexible Ducts Are Different?

If so, how can you buy this type of duct pipe from an online retailer? Because the construction of ducting for mobile homes requires far more restrictive requirements. They differ from the R-rating on their thickness, insulation and the price. If you don’t know exactly why these differences exist, you could be sacrificing HVAC comfort in manufactured homes. The following articles highlight three key differences between insulated mobile home ducting and ductwork. Keep an eye on.

How Much Does It Cost To Replace Ductwork In A Mobile Home?

When a mobile house is bought to renovate, I usually go under the home and look at the ductwork. I will repair or replace the damaged part. Tell me the reason? Old and corroded pipes can cost thousands in energy savings.

Mobile home ducts require higher rating

R-rated ratings show the chances of a ducting system keeping your house warm in the winter and cool during the summer. Its standard insulation measure is accepted by federal agencies, such as IMC and ASHRAE.

In mobile homes, the R-rate is very distinct from apartment or house. While ducted attic ductwork requires R6, buried ductwork requires R3.5 ducting in mobile homes requires R8 insulation. What is the reason for higher R ratings on mobiles? As with mobile homes ductwork, R8 ducts provide more protection and more insulation. They also have higher costs. The normal R-four conduits cost around $1.00 per square meter.

In This Article

Mobile HomeFriend estimates the cost per linear foot to replace electrical wiring is around $3 to $4 per linear foot. A single-wide mobile home can cost about $2200 to $3300. A 2-room, double-wide house requiring 110 ft of ducting could be between $3850 and $650,000. Definitely putting yourself in the role will make it more difficult to crawl beneath your mobile and work in tight conditions. Because this pipe is located underneath the home, this is vulnerable to rodents and if they can enter they can enjoy the warm air. The hoses must be sealed correctly to avoid any potential damage.

Our recommended Flex Duct for Manufactured Homes

We talked about the need for mobile homes to use Flexducts, but it wasn’t a requirement. Now let’s get back to discussing some good Flexduct ducts in mobile homes that are tested. The 25″ wide pipes are R – 8 rated and come in varying lengths (7″, 10″, 12”, 14” or 16”. The exterior has an aluminum covering that is waterproof and withstands the worst weather conditions. The aluminum layers also contain dense fiberglass. The insulation rating therefore exceeded expectations (R-8.2). It’s more expensive than the first and has more stability and protection for flex ducts.

Mobile Home Air Ducts

Mobile Homeducting is constructed with lightweight galvanized sheet metal with a flat square or oval shape to be placed within confined spaces beneath the flooring. The joists can be hung with flexible metal tubes and you will use the same kind if you have the ones you have already.

Flexible ducts are preinsulated, which is nice, because the galvanizing insulation on the duct is another step and costs, and necessary in cold conditions too. Normally fiberboard insulation ducts are not available in an exposed location.

Mobile Home Duct Leakage

So it became especially interesting when a Tucson Aeroseal dealer told me that leaking mobile ducts can cause serious damage to the property. Apparently the construction method of putting together the move-out process and the connection of this equipment at the destination makes mobile home ductwork especially susceptible to duct leakages. When ducted wiring is installed, it can cause multiple damages. As the ductwork for many mobiles is hidden under the home, mice and rats chew through it.

Installation of Home Flex Ducts Are Also Different

Like other homes, a mobile duct is highly susceptible to damp conditions. Particularly the vents which enter kitchens or bathrooms.

This vent is installed beneath the flooring and may flood with spilling water originating in the tub or sink. How does humidity affect the skin? For these reasons, flex ducting around wet areas in mobile homes is a little less rigid than other. There are different things.

Sealing the deal with mobile homes

When talking about home energy saving I must admit I always think about traditional stick house designs. Most people in America live in Mobile Homes – nearly 10m. It seems as though they are just as concerned with energy saving and indoor comfort as they do those living in apartments, condos, or other older mobile homes — perhaps as much as they want. What should you expect?

Mobile Home Flex Ducts Can’t Be Thicker Than 12″

Flex ducts for mobile homes usually do not exceed 12”. Typical in-floor ducting is 20″ thick. It’s likely to be a rare scenario if one had two-wide manufactured homes with a 4-tonne heating pump at the same time. Because the flex pipes are thicker than 12”. Generally speaking mobile homes have maximum insulation of 12″ flexducting. Those were reasons for this.

Because the ductwork lies under the floor a small flame can cause a complete breakdown. It has many limitations on the construction of flex ducting devices in flex homes for fire safety. Let’s get to it.

Ductwork has to be class 0 or 1 For Mobile Home

Most HVAC devices for home appliances like air conditioning and heating equipment are typically fabricated from a metal like galvanised steel or aluminum. However, flex ducting is not by standard conceivable. Specifically, regulations impose mobile home Flex ducts as class zero or class It should not be class Class 2 ducting is no longer manufactured in mobile housing. Anyway, we’ll see what the class and the class mobile home wiring class ducting is. It also applies to air connectors.

Duct must reach me at least 3ft. Away from heat sources

Ideally the conduits should be 3 feet from the furnace bonnet. In reality furnace bonnets and plens are likely to trigger fires within the pipework. It will likely be even more so if the heat source is very near to this vent. They must therefore be within three feet of the furnace and furnace plenum.

The minimum ground clearance factor

The minimum clearance between the floor of an occupied building is 12 inches between the floor. Florida requires a minimum age of 18 years. Because the Flex ducts will be under the walls of your mobile home, they need to be larger than the actual amount needed.

And it could end up destroying the purpose of ground clearing. In case ducting touches the ground, this could cause some problems. This helps prevent pests from entering HVAC systems and causing thousands of dollars worth of damage.

Compression and Kinking Factors

The flex conduits must be supported and suspended to ensure the absence of serious compressor or kinking. The underlying mechanism is normally strapped, or supported by blocks, etc.

If flex pipes’diameters have been greater than 12”, the problem becomes more difficult. Thus, compressors and kinking occurs making a whole air conditioner inefficient and often dangerous.

Fire risk is greater in mobile homes Flex Ducts

Because the ductwork lies under the floor a small flame can cause a complete breakdown. It has many limitations on the construction of flex ducting devices in flex homes for fire safety. Let’s get to it.

They can’t be blocked by obstacles As well

Although they are out of the floor, kitchen ducts in the mobile homes must remain free from clogging. Usually a door or window is too close to a duct to prevent a consistent heat distribution.

For the prevention of leakage of water in bathrooms and kitchens, many of them are installed off floor. It also gives them a less chance of absorbing spilling water & moisture in the water.

What size flex duct for a mobile home?

For mobiles, the ideal size is 12 inches with flexible ducts. The thickness can be as big as 13” and 16” but the floor for mobile homes should have more than that.

Most commonly manufactured residential Flexducts measure 25′ long. You could cut the length down to a more shorter length. Add 2 to your list for longer.

Replace Mobile Home Ductwork

Why Is It So Expensive To Replace Mobile Home Ductwork? Just like the blood veins carry blood from your heart to all locations throughout your body, the ductwork in your home carries the heated or conditioned air from the HVAC unit and distributes it throughout your home.

Also, any leakage from split seams or holes makes the HVAC system operate very inefficiently causing wasted energy and expensive utility bills. Replacing The Mobile Home Ductwork It is not an easy task to remove and replace the ductwork.

Mobile Home Depot offers pages of all the parts needed on their website . Can I install a single HVAC unit outside of the home and remove the air handler from inside the mobile home? Yes, I have done this in a number of mobile home renovations.

LasVegas AC Repair

LasVegas AC Repair

With over thirty years of experience, we’ve been giving air conditioning, heating, pipes, as well as interior air quality solutions to the Las Vegas Valley. As a locally operated family company, we proudly serve our customers with stability and professionalism, and trust. We want you to end up being as well as stay part of our family.

Share:

Get In Touch

Recent Posts